By Robert A. Wilson, Illinois Ballot Integrity Project
February 14, 2006
City of Chicago and Cook County election officials have been touting the new electronic voting technology they plan to use in the March 21st Primary Elections. The equipment, which will be furnished by Sequoia Voting Systems of Oakland, California, will cost more than $50 million to purchase and implement.
More than half of that amount, $25.5 million in taxpayer dollars financed largely from federal grants under the Help America Vote Act (HAVA), will go toward the purchase of about 5,600 Sequoia Optech Insight precinct optical scanners. The balance goes toward the purchase of nearly 6,000 Sequoia AVC Edge DRE (touch-screen) voting terminals, election management software, disability kits, servers, workstations and other equipment and implementation costs. The touch-screens themselves, with their voting card activators, head phones and audio devices will cost about $21 million.
He goes on to say, "The experience with punch-card ballots was less than stellar here and elsewhere. More than 120,000 Cook County voters in 2000 failed to register a choice for president or rendered their choice unusable by piercing holes next to names of two or more candidates."
Sounds awful, doesnt it? Mr. McCormick leaves one with the impression that Chicago and Cook County were using old, out-moded punch-card systems from 1976 and 1982 which he describes as "notorious, failing to give voters a 'second chance'" and failing 120,000 times out of about 1.9 million chances (over 6%) in one election! (more than 72,000 of the undervotes were in the City, a fall-off rate of over 7%, more than double that in the County.
The November, 2000 problem was finally traced by the Illinois Institute of Technology (ITT) to a faulty template mold. Lance Gough, executive director of the Chicago Board of Election Commissioners said on June 3, 2005, "The Board ordered the remanufacture of all the templates, which was completed by the manufacturer at no cost to the City. IIT retested the new templates to ensure that they met the exacting specifications, and tens of thousand of punches were performed to ensure accuracy. These templates have been utilized successfully during the past four elections and have dramatically reduced the number of incomplete ballot punches." LINK
While the faulty mold may have contributed to the unusually high fall-off, the real reason the system under-performed was that the technology to detect overvotes and undervotes was available but simply wasn't turned on! Gough blamed the Illinois State Legislature for failing to pass appropriate legislation that would have allowed City and County election officials to implement the undervote and overvote features of the PBC-2100. According to Gough, " . . . the ballot screening enhancements should have been fully operational for the 2000 Presidential election, but the Illinois state legislature failed to act on several legislative attempts to modify the election code so that ballots could be screened through the PBC-2100. Following the 2000 election fiasco, the City and the County joined in the lawsuit that resulted in a Circuit Court Order allowing for the use of the voter protection features. These ballot screening procedures have been in place since, and have significantly improved voter accuracy and voter confidence."
"Unique among users of the PBC-2100, the Jurisdictions [Chicago and Cook County] use a system that scans a ballot for overvotes and undervotes, giving voters a "second chance" to insure their ballot reflects their intentions."
In its June, 2004 Request for Proposal (RFP) for new voting technology, Chicago and Cook County said, "Unique among users of the PBC-2100, the Jurisdictions [Chicago and Cook County] use a system that scans a ballot for overvotes and undervotes, giving voters a "second chance" to insure their ballot reflects their intentions."
Further, they stated in the specifications, Notification of undervote. Any proposed system must include a mechanism for alerting a voter that he or she has failed to cast a vote for one or more offices or propositions before the vote is finally cast, and to provide an opportunity to correct the undervote. (Specification 3.5 June, 2004)
In fact, the undervote detection capability was so prized by Chicago and Cook County that they asked Sequoia to develop specifications for a blended system by which Chicago would continue to use the PBC-2100 to read ballots, and Sequoia proposed to reprogram the firmware for the PBC-2100 to accept the AVC Edge cartridges and combine the results, thus eliminating the need for the Optech Insight. As Sequoias vice president of sales,Howard Cramer, wrote to Lance Gough on March 7, 2005: . . . it seems clear that both jurisdictions have been pleased with the functionality of the PBC-2100, including the precinct ballot tally . . . and the undervote and overervote warnings incorporated into the system. LINK
In its response to the RFP, Cramer goes on to say, . . . we would also welcome the opportunity to work with you on modifications to the PBC 2100 that would permit you to integrate that equipment with our AVC Edge touch screens equipped with VeriVote printers. The letter includes four pages of flow charts that describe two alternative blended systems while Cramer discusses reprogramming the PBC-2100 fimware (operating system) to accept input from the touch screens and interface with the companys tabulation sofware. In his cover e-mail to the letter, Cramer says, The blended system concept that has really caught fire here is the use of the PBC 2100 to read the Edge cartridges. This seems like the simplest and most cost effective way to accomplish our goals with the least procedural impact on the pollworkers. LINK
So much for hanging chad.